Duerkopp Adler HP Series Additional guide Instrukcja Obsługi Pobierz pdf (Strona 77)

EFKA AB220A511177

Supplier Level

Code no. 311 with control operation

Code no. 3112 with control panel operation

Parameter Designation Unit max min Preset Ind.

307 A1 Signal A1 On/Off 1 0 0 A

308 dA1 Stitches delaying signal A1 stitches 999 0 0 A

309 cA1 Stitch counting during signal A1 stitches 999 0 0 A

310 AA2 Selectable power transistors for signal A2 12 0 0 A

0 =No function

1 =Signal on output M1

2 =Signal on output M2

3 =Signal on output M3

4 =Signal on output M4

5 =Signal on output M5

6 =Signal on output M6

7 =Signal on output M7

8 =Signal on output M8

9 =Signal on output M9

10 =Signal on output M10

11 =Signal on output M11

12 =Signal on output VR

311 So2 Issue signal A2 3 0 0 A

0 =Signal until seam end (according to setting of

parameter 320)

1 =Signal over time

2 =Signal until seam end and drive stops

3 =Signal during stitch counting (according to setting

of parameter 319)

312 tr2 Starting point for signal A2 3 0 0 A

0 =Start at the beginning of the seam

1 =Start of the signal triggered by light barrier sensing

2 =Start of the signal when the drive stops at the seam

end

3 =Start from light barrier covered onwards at the

beginning of the seam

313 do2 Delay of signal A2 2 0 1 A

0 =No delay until signal On

1 =Delay over time until signal On

2 =Delay over stitches until signal On

314 dt2 Delay time until signal A2 On ms 2550 **) 0 0 A

315 St2 ON period of signal A2 ms 2550 **) 0 0 A

316 nA2 Speed mode when signal A2 is On 2 0 0 A

0 =Pedal controlled speed

1 =Limited speed n9

2 =Limited speed n11

317 A2 Signal A2 On/Off 1 0 0 A

318 dA2 Stitches delaying signal A2 stitches 999 0 0 A

319 cA2 Stitch counting during signal A2 stitches 999 0 0 A

320 bP0 Switch-off time of signals A1 and A2 1 0 0 A

0 =Signals effective until seam end

1 =Signals effective until pedal is in pos. 0 (neutral)

321 Std Suppression of the seam when 0 stitches are set 1 0 0 A

0 =Suppression Off

1 =Suppression On

322 dkn 0 =Correction seam Off 2 0 0 A

1 =Correction seam On

2 =Interruption of seam or pattern by thread trimmer

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Duerkopp Adler HP Series Additional guide Instrukcja Obsługi Strona 77

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Maszyny do szycia Duerkopp Adler HP Series Additional guide